磁吸灯箱的标准弧度是多少?

作者:聊城宸宇广告装饰有限公司 时间:2020-05-15 08:58

磁吸灯箱弧形底板模具的制作方法如下:首先用木板或1.8厚密度板制作所需的弧度,标准弧度比为1:3.25。用0.9厘米或1厘米厚的密度板切割所需的尺寸,在底部的每一边各放一个弧度(如果密度板是弧度,将两个弧度固定在一起以增加强度)。用空气钉枪把密度板钉在弧度上。还可以在中间钉几个弧度,另外两边用直密度板可以钉。女模和以前一样。把好的弧度做成与底版相同的模子,底版采用全版钉。当使用0.9厚、1厚或1.2厚的密度板制作圆弧型模具时,密度板厚度的选择是根据字符的大小来决定的(因为密度板的厚度、尺寸和材质决定了弯曲的程度)。
 

磁吸灯箱的标准弧度是多少?
 
  The manufacturing method of the arc base plate mold of the magnetic absorption light box is as follows: firstly, the required radian is made of wood plate or 1.8-thick density plate, and the standard radian ratio is 1:3.25. Use a 0.9CM or 1cm thick density board to cut the required size, and place an arc on each side of the bottom (if the density board is an arc, fix the two arcs together to increase the strength). Use the air nail gun to nail the density board on the arc. You can also nail a few radians in the middle, and you can nail them with a straight density board on both sides. Female models are the same as before. The good radian is made into the same mold as the base plate, and the base plate adopts the full plate nail. When using 0.9-thick, 1-thick or 1.2-thick density plate to make circular arc mold, the selection of density plate thickness is determined by the size of characters (because the thickness, size and material of density plate determine the degree of bending).
 
  磁吸灯箱要把字公模一层钉在弧度板上,在字内钉上同样的弧度。根据亚克力板的物理特性,冷却时间为24小时,至少12小时使用。亚克力底板的冷却方法:将亚克力底板从平台上取下后,翻转至四边的底部,用托架垫起,让底板悬空不让亚克力地板表面着地。每个中间部分的上部的四个边的丙烯酸底板与沉重的重量压实,然后吹尘枪肩并肩用手轻轻按其表面,使其逆转的表面快速冷却集。按一段时间。阴阳模具完成后,用砂纸或锉刀对阳模的四边和四条腿进行加工,使棱角略圆。角落稍微倾斜,以释放模具。在模具底部撒上沙子。不管弧形地板模具中间的弧度有多大,都要尽量保证两边高度在3cm左右。过高难以形成后的四边板很容易开裂。,压吸成型。十八、制作方法弧形文字模具要做与底版模具相同的弧度,根据底版的尺寸取弧度在中间比字体稍大的部分。当你做这个弧度时,你必须同时保持内弧和外弧。亚克力字冷却法:亚克力字从平台上取下,放在平整的地方,四面压重,以防底部变形。
 
  The magnetic absorption light box shall nail the common mould of the characters on the arc plate, and nail the same arc in the characters. According to the physical properties of acrylic plate, the best cooling time is 24 hours, at least 12 hours. Cooling method of acrylic base plate: after taking the acrylic base plate off the platform, turn it to the bottom of four sides, and pad it with bracket, so that the base plate is suspended and the acrylic floor surface does not touch the ground. Each middle part of the upper four sides of the acrylic base plate is compacted with heavy weight, and then the dust gun side by side gently presses its surface with hand, so that it reverses the surface of the rapid cooling set. Press for a period of time. After the completion of the male and female mold, the four sides and four legs of the male mold are processed with sandpaper or file to make the edges and corners slightly round. The corners tilt slightly to release the mold. Sand the bottom of the mold. No matter how large the arc is in the middle of the arc floor mold, try to ensure that the height of both sides is about 3cm. It is very easy to crack the quadrilateral plate when it is too high to form. Finally, the pressure absorption molding. 18、 The method of making arc text mould is to make the same radian as that of the base mould. According to the size of the base, the radian in the middle is slightly larger than the font. When you do this arc, you have to keep the inner arc and the outer arc at the same time. Acrylic cooling method: remove the acrylic from the platform and place it in a flat place with four sides pressed to prevent deformation of the bottom.

转载请标明出处,本页地址:http://www.chenyuguanggao.com/news/wiki/203.html


当前位置:主页 > 广告资讯 > 广告行业百科 >
上一篇:简单介绍标识标牌     下一篇:没有了